주요특징
- 통신 이중화 듀얼타입 네트워크 어댑터를 통해 “Active – Standby “ 방식으로 통신 이중화 구현 , Active 모듈 문제 발생 시 , Standby 모듈이 즉시 동작하여 안정적인 통신을 유지 가능
- 파워 이중화 전원 문제 발생 시 외부 노이즈로부터 통신, 네트워크를 보호하고 전원 문제 시 발생할 수 있는 손실을 방지
- 핫스왑 Backbone 구조로 인해 전원이 인가된 상태에서도 모듈 착탈이 가능하며, 유지보수 시에도 설비 멈춤없이 안정적 유지 보수 및 교체 가능
| ML9089 (Ethernet TCP/IP NETWORK ADAPTER Light) | |
|
Adapter Type |
Slave node (Ethernet TCP/IP), Single, Light |
| Protocol | MODBUS/TCP,MODBUS/UDP, Ethernet/IP, CC-Link Field Basic |
| Sub-Protocol | HTTP, DHCP, 10 TCP Connections, SLMP |
| Max. Expantsion Module |
16 slots |
| Modbus Max. Data Size | Max Input 256 bytes / Max Output 256 bytes |
| Max Length Bus Line | Up to 100m from Ethernet Hub/Switch with twisted CAT5 FTP/STP |
| Max. Data Size(RX, RY) | each 32 bytes (4 Stations occupied) |
| Max. Data Size(RWr, RWw) | each 256 bytes (4 Stations occupied) |
| Max. link points per station (RX, RY) | each 64 points |
| Max. link points per station (RWr, RWw) | each 32 points |
| Max. Nodes |
Limited by Ethernet Specification. |
| Baud Rate |
10/100Mbps, Auto-negotiation, Full duplex |
|
Interface Connector |
RJ-45 socket * 2pcs |
| IP-Address Setup | Via DHCP/BOOTP or IOGuide(Crevis Software) |
| IP-Address Range | xxx.xxx.xxx.1 ~ 253 (User area) |
| IAP Mode | When DIP Switch 1 to 8 setting is 254 or 255 (Using only Internet Explorer / recommended version 11 ) |
| Indicator | 4 LEDs 1 Green/Red, Module Status (MOD) 1 Green, Physical Connection (LINK) 1 Green, Exchange Data/Traffic Present (ACTIVE) 1 Green/Red, Expansion I/O Module Status (IOS) |
| Module Location | Starter module left side of M-Series system |
| General Specification | |
| UL System Power | Supply voltage : 24Vdc nominal, Class 2 |
| System Power |
Supply voltage : 24Vdc nominal |
| Power Dissipation | Network Adapter : 60mA typical @ 24Vdc |
| Current for I/O Module | 1.0A @ 5Vdc |
| Isolation |
System power to internal logic : Non-isolation |
| UL Field Power | Supply voltage : 24Vdc nominal, Class 2 |
| Field Power |
Supply voltage : 24Vdc typical (Max.28.8Vdc) |
| Max. Current Field Power Contact | DC 8A Max |
| Torque | 0.8Nm(7 lb-in) |
| Single Wire | 0.205㎟ - 1.3㎟ (24-16 AWG) |
| Weight | 83g |
| Module Size |
23mm x 110mm x 75mm |
| Environment Condition | Refer to ‘1. Environment Specification’ |
| Pin No | Signal Description |
| 1 | System Power, 24V |
| 2 |
System Power, Ground |
| 3 | F.G |
| 4 | Field Power, Ground |
| 5 |
Field Power, 24V |