주요특징
- 통신 이중화 듀얼타입 네트워크 어댑터를 통해 “Active – Standby “ 방식으로 통신 이중화 구현 , Active 모듈 문제 발생 시 , Standby 모듈이 즉시 동작하여 안정적인 통신을 유지 가능
- 파워 이중화 전원 문제 발생 시 외부 노이즈로부터 통신, 네트워크를 보호하고 전원 문제 시 발생할 수 있는 손실을 방지
- 핫스왑 Backbone 구조로 인해 전원이 인가된 상태에서도 모듈 착탈이 가능하며, 유지보수 시에도 설비 멈춤없이 안정적 유지 보수 및 교체 가능
| M7001 (Redundancy Power Module) | |
System Input Voltage Range |
15Vdc to 28.8Vdc |
| UL System Power | Supply voltage : 24Vdc nominal, Class 2 |
| System Power Input Volrage | Supply voltage : 24Vdc nominal Supply voltage range : 15~28.8Vdc Protection : Output current limit Reverse polarity protection |
| Indicators | 4 LEDs 1 Green, M-Bus Status (RUN) 1 Green, Primary Status(PRI) 1 Green, Active Status (ACT) 1 Green, Field Power Enable (Field Power) |
| UL Field Power | Supply voltage : 24Vdc nominal, Class 2 |
| Field Power Input Voltage | Supply voltage : 24Vdc typical(±20%) * Field Power Range is different depending on IO Module series. Refer to IO Module`s Specification. |
| M-bus Output Voltage | Max 5Vdc, 2A |
| General specification | |
| Power dissipation | Max. 20mA @ 24Vdc |
| Single Power Current for I/O Module | 2.0A @ 5Vdc Test Voltage Condition : 28.8V - The Base can be used up to 50℃ - You should use dummy module(M7000) at 60℃ * Refer to ‘2.7 Dummy Module Location |
| Expansion Power | Refer to ‘2.5. Power Expansion Function’ |
| Isolation | System power to internal logic : Non-isolation System power I/O driver : Isolation |
| Max. Current Field Power Contact | DC 10A Max |
| Single Wire | 0.205㎟ - 1.3㎟ (24-16 AWG) |
| Torque | 0.8Nm(7 lb-in) |
| Weight | 72g |
| Module Size | 12mm x 110mm x 75mm |
| Hot Swap | Possible |
| Pin No. | Signal Description |
| 0 - SP | System Power, 24V |
| 1 - SP | System Power, 24V |
| 2 - SN | System Power, 0V(GND) |
| 3 - SN | System Power, 0V(GND) |
| 4 - NC | - |
| 5 -NC | - |
| 6 - PS | Primary Power Setting |
| 7 - PS | Primary Power Setting |
| 8 - FG | F.G |
| 9 - FG | F.G |
| 10 - FN | Field Power 0V (GND) |
| 11 - FN | Field Power 0V (GND) |
| 12 - FN | Field Power 0V (GND) |
| 13 - FN | Field Power 0V (GND) |
| 14 - FP | Field Power 24V |
| 15 - FP | Field Power 24V |
| 16 - FP | Field Power 24V |
| 17 - FP | Field Power 24V |